Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Part Out Feeler
#1
So i've been trying to sell the focus for a while, fact is I haven't drove it more than 3 weeks in the past two years so its time to go. The car is mint, but if I can get the major parts sold i'll take the time and part it out completely. If someone has $6000 right now they can come and take the car, otherwise parted out down to the frame and scrap the rest. (provided there is enough interest in parts)

I have it in the trader right now, and hopefully someone buys it. If anybody is serious about the parts/prices listed below let me know. I think the prices are fair, like the tranny, the LSD alone costs almost $800. The rubber on the rims cost $600 and never was used.

FS Stage 3 Supercharger - $2200
- 60# siemens inj.
- Boost Gauge
- All hoses/clamps, pumps, screws, etc.
- Includes key and ecu and flasher locked to ecu.
- Front mount intercooler, resevoir, and PWR liquid air intercooler
- CFM Overdrive Pulley
- Vortech S/C
- 20,000km on base kit
- 5,000km on stage 3 (intercooler)

FS Polished Valve Cover - $150 (available now)
FS Oil Cooler - $80
FS Headers - $80
Built Tranny w/
- Spec Stage 3 Clutch
- 4.07 Final Drive Gears
- Torsen T2 LSD
- FS Lightweight Flywheel
$800

Bosal Flex Pipe - $60
FS Stealth Exhaust - $180
Taylor Battery Relocation Kit + Optima Yellow Top Battery (brand new) - $200
Steeda Fuel Rail - $60
VF Engine Mounts (dogbone and driver) - $120 for both
FK Coilovers - $500
Hella Projectors w/ HID Conversion - $400
Clear Lense Grill - $50
Velox VX6r Rims (14lb each) + Falken RT-615 tires (brand new rubber!) - $700
VIS CF Invader Hood + Stock Hood in good Shape - $400
Stock Hood Liquid Grey - $80
LC-1 Wideband with Gauge - $180
SVT Cluster - $60
SVT Seats (red/black) + Door Inserts - $500
Full Interior (dash,carpet, headliner) - $100
Zetec Engine w/ 78,000 Focus Sport Kent Cams/Gears - $300
Focussport rear strut bar(black) - $60
Custom Gauge Surrounds for Gauges (radio + cluster bezel) - $80
F2 Body Kit - $500
Reply
#2
The rear strut bar, does that mount to the top of the rear struts or is that the one where you need to drill out a spot weld on either side? I may be interested. Will a stroller still fit if it is in place?

Actually I am interested in quite a bit but the funding isn't there. :iono:
Focus man, Focus........ Team Psychological Disaster
2008 Taurus X to be modded.
2002 ZX5 parted out. Forever known as the "SLOCUS".

2010 Dyno #'s 102.96HP/105.84TQ
2011 Dyno #'s 111.44HP/115.17TQ
Still The Weakest LinkBlush

Dial 1-800-AUTO-PARTS for your local speed shop.
Reply
#3
if you are going to tore down everything, count me in for transmission with other wiring, so i can do manual swap..

how much would you say for whole tranny assembly??wiring, pedal, brake reservoir, shift assy, ecu + 2 keys??
Reply
#4
Great deal on that supercharger kit, It's too bad I have my car up for sale because if I was buying parts I would be allll over that tranny.
DruZX3 You Tube Page
My Rides on Car Domain

2001 Ford Focus ZX3 - Daily Driver
2008 Lincoln MKX Limited Edition - Grocery Getter
2007 Suzuki GSXR 600 - Rode and Sold
2004 Jeep Liberty Renegade - Offroaded and Sold
2008 Jeep Wrangler Unlimited X - R.I.P. Electrical Fire
2000 Ford Focus ZX3 - Traded in Now DrunkinMonkeys Car
2003 Ford Taurus Wagon - Inherited Drove and Sold
2000 Ford Focus ZX3 Turbo - Award Winning 336 WHP - Parted and Scraped
1990 Ford Festiva - My 1st Car

[Image: ZX3PixelCarEngineVIEW.png]
Reply
#5
konafocuswrc2,Jul 16 2009, 09:56 AM Wrote:if you are going to tore down everything, count me in for transmission with other wiring, so i can do manual swap..

how much would you say for whole tranny assembly??wiring, pedal, brake reservoir, shift assy, ecu + 2 keys??
[right][snapback]291166[/snapback][/right]

Unfortunatly ECU goes with S/C for tuning. For the rest $950 for full tranny + other hardware minus ecu and keys.

Reply
#6
would you be willing to sell the front and rear F2 bumpers alone? if you are then I'll take them....and I live close by so it would be easy.
Reply
#7
i would love to take that engine
2000 dark violet pearl zx3: eagle rods, je pistons, fidanza cam gears, arp studs, ford racing highlift valve springs, svt front/rear disc conversion, prothane total kit, fc 65mm throttle body Tial gt3071r, tial mvs wastegate, tial Q bov, top speed "street" manifold,down pipe and dump tube, greddy boost controller, siemens deka #61 injectorz, stage 4 bully clutch way to much more to list
Instagram @o_so_slo
Reply
#8
Focus man, Focus.,Jul 16 2009, 08:39 AM Wrote:The rear strut bar, does that mount to the top of the rear struts or is that the one where you need to drill out a spot weld on either side?  I may be interested.  Will a stroller still fit if it is in place?

Actually I am interested in quite a bit but the funding isn't there.  :iono:
[right][snapback]291161[/snapback][/right]

OK I researched and I believe it ios the Drill out Spot Weld to Install. Still interested.
Also wouldn't mind the Exhaust but I would have to start rolling my change. :rolleyes:

Although, it would make a nice Birthday present. :rofl:
Focus man, Focus........ Team Psychological Disaster
2008 Taurus X to be modded.
2002 ZX5 parted out. Forever known as the "SLOCUS".

2010 Dyno #'s 102.96HP/105.84TQ
2011 Dyno #'s 111.44HP/115.17TQ
Still The Weakest LinkBlush

Dial 1-800-AUTO-PARTS for your local speed shop.
Reply
#9
Wow alot of good stuff here and good prices.....PM was sent
E.O Masiv!
New look for the summer
SVT ZX5 Focus Build#56 01/29/2003
I think there is something wrong with my car, every time I shift I hear Psssst noise?
Looking to get 25-30psi with a Procharger


[Image: style7,TikEtZ.png]
Reply
#10
oh man i can't believe you're thinking of doing a part out....

[Image: n509207701_780207_801.jpg]

:yikes:
2002 pitch black ZX3
__________________
Mach HIDs, 02 RS upper grille, Cervini's body kit, DTM drop mirrors, D2 coilovers, purple focussport strut tower bar and chrome rear bar, purple FC tb, Powerworks supercharger, optima yellow top, SVT ceramic coated header,Random Tech SVT/Zetec hi-flow cat , bosal flex, vibrant cat back with custom dual tips, b&m short throw shifter, pro-fit fuel door, shorty antenna, race-pedals.com "focus" pedals, clear 3rd brake light, SVT hvac controls, Transfer Racing billet hvac knobs, RS shift knob, RS Sparco E-brake handle, Mazda3 rear wiper, CarZone 3 piece roof wing, 17" Keskin KT4 wheels

Classic Painting
Reply
#11
hardk0re,Jul 16 2009, 10:36 AM Wrote:
konafocuswrc2,Jul 16 2009, 09:56 AM Wrote:if you are going to tore down everything, count me in for transmission with other wiring, so i can do manual swap..

how much would you say for whole tranny assembly??wiring, pedal, brake reservoir, shift assy, ecu + 2 keys??
[right][snapback]291166[/snapback][/right]

Unfortunatly ECU goes with S/C for tuning. For the rest $950 for full tranny + other hardware minus ecu and keys.
[right][snapback]291176[/snapback][/right]

$950 sounds awesome deal to me!!
let me know when you actually parting out..
Reply
#12
Any pics of the the :

*strut bar
*interior items that are for sale
*exhaust

Thanks
Reply
#13
Wow, will be so sad to see this part out.
I wonder if the car would pass Quebec's safety check, lol.
2007 CD Silver ST  **** FOR SALE ****
2014 Performance Blue ST  **** SOLD ****

2016 Ford Edge Sport Shadow Black
Reply
#14
i got $950 in my hands waiting you to part out, lol
BLACKBOX(DASHCAM) | LED | HID | REMOTE STARTER + SECURITY | 12 VOLT ACCESSORIES | CAR ENTERTAINMENT | PERFORMANCE UPGRADE | MAINTENANCE REPAIR
[Image: banner_468x60_zps1c433cb9.gif]
info@motormaniac.ca | 905.508.3737
If you are calling after hours, please leave a pm or detailed voice mail and we will get back to you as soon as possible.
Reply
#15
dont part this car out!!!
Sean- 1998.5 Black/Blue CSVT #5906

Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)